What's missing on Mammoth electronics

Mammoth-related discussion of pedal parts, questions, and DIY builds!

Moderators: Ghost Hip, blakemoth

Post Reply
User avatar
Jero
IAMILFFAMOUS
IAMILFFAMOUS
Posts: 11290
Joined: Fri Mar 12, 2010 1:12 am
Location: here

Re: What's missing on Mammoth electronics

Post by Jero »

kato wrote:1790NS Enclosures
pot condoms
trimpots in a few more standard values
PCB-mount 3PDT stompswitches

They have pcb mount 3pdt...notice the switch pcbs they offer :thumb:
and I agree about the trimpots
I make noise toys under Stomping Stones
[url=http://www.stompingstones.com[/url]
oldangelmidnight wrote:This is the classic ILF I love. Emotional highs and lows. Scooped mids in my heart all day long.
kato
uncommitted
uncommitted
Posts: 4
Joined: Thu Nov 17, 2011 6:48 pm

Re: What's missing on Mammoth electronics

Post by kato »

Jero wrote:They have pcb mount 3pdt...notice the switch pcbs they offer :thumb:



Oh yeah, I see those. But I'm building a four knob rat where the switch goes directly through the PCB:

Image

Looking at the Industrial Series 3PDT, the pins look small enough that I could probably snip snip and file them down to fit in the PCB holes:

Image

So 86 that request for PCB mount stompswitches. An industrial switch is added to my cart.
User avatar
skullservant
IAMILFFAMOUS
IAMILFFAMOUS
Posts: 16575
Joined: Wed Dec 28, 2011 12:55 am

Re: What's missing on Mammoth electronics

Post by skullservant »

lowbrow wrote:It's been said once, but:

Transistor sockets!


The only thing thats missing for me Blake! Love the addition of Switchcraft!
Officer Bukowski
IAMILFFAMOUS
IAMILFFAMOUS
Posts: 3307
Joined: Wed Nov 17, 2010 9:13 pm

Re: What's missing on Mammoth electronics

Post by Officer Bukowski »

Could you guys start selling heat shrink? I know I could easily grab some at the hardware store but I'd rather buy it from you guys.
I make pedals. SHARK TANK
User avatar
Jwar
Cosmic of BILF
Cosmic of BILF
Posts: 18238
Joined: Thu Dec 02, 2010 7:18 pm
Location: The edge of existence

Re: What's missing on Mammoth electronics

Post by Jwar »

Does Mammoth sell the following

3.3 m resistors
1uf caps
"I do not have the ability to think rationally 90% of the time and I also change my mind at the drop of a hat".

-JWAR :)
User avatar
Jero
IAMILFFAMOUS
IAMILFFAMOUS
Posts: 11290
Joined: Fri Mar 12, 2010 1:12 am
Location: here

Re: What's missing on Mammoth electronics

Post by Jero »

jwar wrote:Does Mammoth sell the following

3.3 m resistors
1uf caps

They have every type of 1uf you could need, but don't have much in the Meg department.
I make noise toys under Stomping Stones
[url=http://www.stompingstones.com[/url]
oldangelmidnight wrote:This is the classic ILF I love. Emotional highs and lows. Scooped mids in my heart all day long.
User avatar
fuzzmax
experienced
experienced
Posts: 917
Joined: Tue Apr 06, 2010 7:30 am
Location: Joliette, Quebec

Re: What's missing on Mammoth electronics

Post by fuzzmax »

davies 1470 knobs.
User avatar
Gone Fission
IAMILFFAMOUS
IAMILFFAMOUS
Posts: 4833
Joined: Sat Dec 04, 2010 1:50 pm
Location: The ungovernable tribal regions southwest of D.C.
Contact:

Re: What's missing on Mammoth electronics

Post by Gone Fission »

Bring back multi-pack blem enclosures. How did you run out? You're not being careless enough, I guess.
D.o.S. wrote:Broadly speaking, if we at ILF are dropping 300 bucks on a pedal it probably sounds like an SNES holocaust.
friendship wrote:death to false bleep-blop
UglyCasanova wrote:brb gonna slap my dick on my stomp boxes
brand0nized
uncommitted
uncommitted
Posts: 1
Joined: Fri Apr 13, 2012 2:28 am

Re: What's missing on Mammoth electronics

Post by brand0nized »

Something I would REALLY like to see:
1590LB Color Choices!!! Even the 1590A has it, why not the LB?
coldcraft
uncommitted
uncommitted
Posts: 1
Joined: Fri Feb 11, 2011 3:57 pm

Re: What's missing on Mammoth electronics

Post by coldcraft »

will powder coated looper cases be added at some point?
Officer Bukowski
IAMILFFAMOUS
IAMILFFAMOUS
Posts: 3307
Joined: Wed Nov 17, 2010 9:13 pm

Re: What's missing on Mammoth electronics

Post by Officer Bukowski »

I love the new stuff you guys have been adding. The looper enclosures look great!

I wish you guys had PCB standoffs though. I can't seem to find them anywhere really
I make pedals. SHARK TANK
Bret608
committed
committed
Posts: 115
Joined: Thu Jun 03, 2010 4:07 pm
Location: Madison, Wisconsin

Re: What's missing on Mammoth electronics

Post by Bret608 »

Officer Bukowski wrote:I love the new stuff you guys have been adding. The looper enclosures look great!

I wish you guys had PCB standoffs though. I can't seem to find them anywhere really


I've only seen the standoffs at Pedal Parts Plus (under accesories; they have two kinds) and in the parts store on BYOC, if I remember correctly.

I agree that Blake has added a lot of useful items recently.
Twisted
uncommitted
uncommitted
Posts: 5
Joined: Fri May 04, 2012 9:40 am

Re: What's missing on Mammoth electronics

Post by Twisted »

Hey all,
I am a noob here and just found Mammoth. Everything I've been getting from separate vendors all at one place, and with good prices at that.

I am very impressed (in addition) when reading this thread after browsing all the good stuff and realizing that several of the things I saw that I liked where requested here. This shows a a group of people (Mammoth) that care about their customers, can act quickly to improve their business, and probably don't have many committee meetings (heh heh). I work for the state, and to do something new (heaven forbid) it takes months - nay, years of meetings just to do the wrong thing much too late.

Anyway, I create my own PCBs and would like to see single sided copper blank not pre-drilled PCB boards. I usually just go to Radio Shack for those, but they only carry double sided, and that's just an extra pain to etch all that wasted copper from the top of the board.

I would love to see 1/32 drill bits for this purpose as well. The smallest any hardware store carries is 1/16 (unless you get the Dremel kit for $11 just for the one out of 5 bits you want). I have to make my boards larger to accommodate the larger holes and pads.

I could order this stuff online elsewhere, but would rather order it from Mammoth.

Anyone out there etch your own PCBs? It makes for a very professional look, helps with external noise (especially with a solid ground plane which also uses less solution and goes faster), and is very easy/cheap to do. I'll post in a more appropriate forum how to do it (or just Google it), but I've tried several methods and found one that is real easy and works well, including making your own etching solution from vinegar, hydrogen peroxide and salt. I get hungry every time I etch a board because it smells like salad dressing ;)
User avatar
blakemoth
involved
involved
Posts: 69
Joined: Fri Aug 05, 2011 4:27 pm
Location: Oklahoma, USA
Contact:

Re: What's missing on Mammoth electronics

Post by blakemoth »

Officer Bukowski wrote:I love the new stuff you guys have been adding. The looper enclosures look great!

I wish you guys had PCB standoffs though. I can't seem to find them anywhere really


PCB Standoffs just added. Both the aluminum hex style (3 different sizes) as well as the plastic adhesive style : http://www.mammothelectronics.com/category-s/130.htm
Officer Bukowski
IAMILFFAMOUS
IAMILFFAMOUS
Posts: 3307
Joined: Wed Nov 17, 2010 9:13 pm

Re: What's missing on Mammoth electronics

Post by Officer Bukowski »

I just saw this in your newsletter. Thanks for being so awesome and listening to your customers :hug:

I'll be buying a whole bunch of stuff from you guys in the near future
I make pedals. SHARK TANK
Post Reply