What's missing on Mammoth electronics

[Jero]

1790NS Enclosures
pot condoms
trimpots in a few more standard values
PCB-mount 3PDT stompswitches

They have pcb mount 3pdt...notice the switch pcbs they offer
and I agree about the trimpots

[kato]

They have pcb mount 3pdt...notice the switch pcbs they offer

Oh yeah, I see those. But I'm building a four knob rat where the switch goes directly through the PCB:



Looking at the Industrial Series 3PDT, the pins look small enough that I could probably snip snip and file them down to fit in the PCB holes:



So 86 that request for PCB mount stompswitches. An industrial switch is added to my cart.

[skullservant]

It's been said once, but:

Transistor sockets!

The only thing thats missing for me Blake! Love the addition of Switchcraft!

[Officer Bukowski]

Could you guys start selling heat shrink? I know I could easily grab some at the hardware store but I'd rather buy it from you guys.

[Jwar]

Does Mammoth sell the following

3.3 m resistors
1uf caps

[Jero]

Does Mammoth sell the following

3.3 m resistors
1uf caps

They have every type of 1uf you could need, but don't have much in the Meg department.

[fuzzmax]

davies 1470 knobs.

[Gone Fission]

Bring back multi-pack blem enclosures. How did you run out? You're not being careless enough, I guess.

[brand0nized]

Something I would REALLY like to see:
1590LB Color Choices!!! Even the 1590A has it, why not the LB?

[coldcraft]

will powder coated looper cases be added at some point?

[Officer Bukowski]

I love the new stuff you guys have been adding. The looper enclosures look great!

I wish you guys had PCB standoffs though. I can't seem to find them anywhere really

[Bret608]

I love the new stuff you guys have been adding. The looper enclosures look great!

I wish you guys had PCB standoffs though. I can't seem to find them anywhere really

I've only seen the standoffs at Pedal Parts Plus (under accesories; they have two kinds) and in the parts store on BYOC, if I remember correctly.

I agree that Blake has added a lot of useful items recently.

[Twisted]

Hey all,
I am a noob here and just found Mammoth. Everything I've been getting from separate vendors all at one place, and with good prices at that.

I am very impressed (in addition) when reading this thread after browsing all the good stuff and realizing that several of the things I saw that I liked where requested here. This shows a a group of people (Mammoth) that care about their customers, can act quickly to improve their business, and probably don't have many committee meetings (heh heh). I work for the state, and to do something new (heaven forbid) it takes months - nay, years of meetings just to do the wrong thing much too late.

Anyway, I create my own PCBs and would like to see single sided copper blank not pre-drilled PCB boards. I usually just go to Radio Shack for those, but they only carry double sided, and that's just an extra pain to etch all that wasted copper from the top of the board.

I would love to see 1/32 drill bits for this purpose as well. The smallest any hardware store carries is 1/16 (unless you get the Dremel kit for $11 just for the one out of 5 bits you want). I have to make my boards larger to accommodate the larger holes and pads.

I could order this stuff online elsewhere, but would rather order it from Mammoth.

Anyone out there etch your own PCBs? It makes for a very professional look, helps with external noise (especially with a solid ground plane which also uses less solution and goes faster), and is very easy/cheap to do. I'll post in a more appropriate forum how to do it (or just Google it), but I've tried several methods and found one that is real easy and works well, including making your own etching solution from vinegar, hydrogen peroxide and salt. I get hungry every time I etch a board because it smells like salad dressing

[blakemoth]

I love the new stuff you guys have been adding. The looper enclosures look great!

I wish you guys had PCB standoffs though. I can't seem to find them anywhere really

PCB Standoffs just added. Both the aluminum hex style (3 different sizes) as well as the plastic adhesive style : http://www.mammothelectronics.com/category-s/130.htm

[Officer Bukowski]

I just saw this in your newsletter. Thanks for being so awesome and listening to your customers

I'll be buying a whole bunch of stuff from you guys in the near future