The Cosmichorus v3 Pre-Order Package Partypalooza!

[Clean Channel]

Don't say the "C" word 'round here.

Did I say the wrong thing?

Its been asked before...you aint getting a compressor form the good doc. Go grab a diamond compressor and be done with it.

Or get the empress and really be done with it.

[Tompski]

Ok got it!

[bronzetalon]

Part 4! Synced

[youtube]http://www.youtube.com/watch?v=ucvQfqM4DmI[/youtube]

[goroth]

Just got back from holidays and found a Cosmi waiting on the kitchen table (gotta love having in laws checking the post). So much zombie fun. Thanks Ryan!

[excane]

Part 4! Synced

[hollowhero]

Does the second expression jack control the clock knob or does it allow me to change the lfo shape and depth?

[01010111]

There are not words yet invented to describe my joy for this box so I will say that it is erasculitiously meinfergating and vorculatious

The controls are very different from what I'm used to on chorus type effects, but they're actually becoming fairly intuitive. I was wondering about the CV-in for tempo, could you just use an external tap-tempo thinger that wasn't CV? I have a DMMTT550 that has an external tap tempo input, and I was wondering if I could rig something up to send a single tap-tempo signal to both pedals.

[bronzetalon]

Does the second expression jack control the clock knob or does it allow me to change the lfo shape and depth?

Rate and depth, I used depth in my video because if I used rate it would modulate through a sweep of rates.

There are not words yet invented to describe my joy for this box so I will say that it is erasculitiously meinfergating and vorculatious

The controls are very different from what I'm used to on chorus type effects, but they're actually becoming fairly intuitive. I was wondering about the CV-in for tempo, could you just use an external tap-tempo thinger that wasn't CV? I have a DMMTT550 that has an external tap tempo input, and I was wondering if I could rig something up to send a single tap-tempo signal to both pedals.

Basically no you need something that has a cv out. The tap tempo in on your dmm is merly looking for a momentary switch to set tempo. The ccv3 has no way to directly take a tap tempo like that.

[01010111]

Thanks! I was really hoping for it to be a tap tempo inputs so I could just plug one momentary switch into both for kewl synchronized delays and chorusing, will have to work on a cv solution to this...

[bronzetalon]

A copilot broadcast with two outputs might work.

[Ryan]

Awesome synced video, Ian, that's really cool!

Thanks! I was really hoping for it to be a tap tempo inputs so I could just plug one momentary switch into both for kewl synchronized delays and chorusing, will have to work on a cv solution to this...

Pedals that you can do that are digital and already have a computer inside that can make tap tempo, it's not like the Cosmi at all. I hear this a lot, people think you can just 'plug in' tap tempo but that's now how it works.

Tap tempo requires a computer to count how many times the stomp switch touches ground and then convert that timing into a bpm or specific rate based off that counter. It requires a full microprocessor with a page or two of code and you have to interface a digital control section with the analog section. It's a big complicated addition to an analog circuit and depending on the nature of the analog clock circuitry, might not even be possible.

Expression/CV inputs just require a waveform/voltage plugged in, that's all they can work with, it's an analog system.

[Tompski]

[youtube]nLFS9rvE1b4[/youtube]

#42

[excane]

[youtube]nLFS9rvE1b4[/youtube]

#42

There ya go

[youtube]http://www.youtube.com/watch?v=nLFS9rvE1b4[/youtube]

[bronzetalon]

[youtube]nLFS9rvE1b4[/youtube]

#42

Nice demo Tompski, much better tone and playing than my half baked demos.

[Tompski]

Thanks Excane! I was there for flipping ages trying to work that out! What was I doing wrong? I managed to do it right on The Gear Page.

And thanks Bronzetalon, I like your demos