Help fix my GB24?

General Gear Discussion - effects, synths, etc.

Moderator: Ghost Hip

Post Reply
User avatar
JonnyAngle
IAMILFFAMOUS
IAMILFFAMOUS
Posts: 4233
Joined: Wed Feb 25, 2015 11:35 am
Contact:
Contact JonnyAngle

Help fix my GB24?

Post by JonnyAngle »

Tldr: bypassed signal passes through. Muted when led is on

All of the wires soldered to the switch have good connections and pass continuity. I emailed Scott, but I'm not patient. Especially if it's something I can do myself.

Any ideas????? :hug:

https://youtu.be/iAoniPOpuFU
Top
User avatar
D.o.S.
IAMILFFAMOUS
IAMILFFAMOUS
Posts: 29881
Joined: Sun Jul 03, 2011 8:47 am
Location: Ewe-Kay

Re: Help fix my GB24?

Post by D.o.S. »

Turn the second knob down off of noon?

:p
good deals are here.
flesh couch is here.
UglyCasanova wrote: It's not the expensive programs you use, it's the way you click and drag.
Achtane wrote:
comesect2.0 wrote:Michael Jackson king tut little Richard in your butt.
IT'S THE ENNNND OF THE WORRRLD AS WE KNOW IT
Top
User avatar
JonnyAngle
IAMILFFAMOUS
IAMILFFAMOUS
Posts: 4233
Joined: Wed Feb 25, 2015 11:35 am
Contact:
Contact JonnyAngle

Re: Help fix my GB24?

Post by JonnyAngle »

D.o.S. wrote:Turn the second knob down off of noon?

:p
Ha! That's just a coincidence for the video.
Top
User avatar
baremountain
FAMOUS
FAMOUS
Posts: 1164
Joined: Mon Jun 27, 2016 2:19 pm
Location: Dallas, TX
Contact:
Contact baremountain

Re: Help fix my GB24?

Post by baremountain »

My Ct5 did this (or something very similar) and it was a bad solder point on one of the jacks I think.
Inner Vegas wrote:I don't think anyone is Obama
#wheresthebirthcertificate #obamahoax

solo tunes:
completed works || loosey goosey releases
associated acts:
Raab Zamboni (fake jazz/real noise//sax, modular synth, editing, misc) || Field Guide (my best friends//sax on 2 tracks)

I make t-shirts, patches, koozies, buttons, CDs, sometimes tapes, and eventually i'll start working on pedals again. DM me for pricing!
Top
User avatar
rustywire
IAMILFFAMOUS
IAMILFFAMOUS
Posts: 4715
Joined: Thu Dec 13, 2012 9:54 am
Location: on.

Re: Help fix my GB24?

Post by rustywire »

:cry:
[B/S/T shoutouts] Shortlist: Hollow Earth|Ct5|856|Condor|Thermae|OP-1|half track reel2reel|Prophet6 ... :whoa:
rfurtkamp wrote:The only transparent thing I own is a set of drinking glasses.
Image
Top
User avatar
Jwar
Cosmic of BILF
Cosmic of BILF
Posts: 18239
Joined: Thu Dec 02, 2010 7:18 pm
Location: The edge of existence

Re: Help fix my GB24?

Post by Jwar »

Send it to me. I'll either A)fix it or B)break it by accident. Your loss is your loss???

Sorry I'm absolutely no help. LOL
"I do not have the ability to think rationally 90% of the time and I also change my mind at the drop of a hat".

-JWAR :)
Top
User avatar
crochambeau
IAMILF
IAMILF
Posts: 2219
Joined: Mon Jul 20, 2015 12:49 pm
Location: Cascadia
Contact:
Contact crochambeau

Re: Help fix my GB24?

Post by crochambeau »

JonnyAngle wrote:All of the wires soldered to the switch have good connections and pass continuity. I emailed Scott, but I'm not patient. Especially if it's something I can do myself.
How far "in" have you confirmed continuity?

Have you measured voltages on the Vcc pins yet?
Top
User avatar
blakestree
IAMILF
IAMILF
Posts: 2305
Joined: Fri Dec 05, 2014 3:36 pm
Location: Savannah, GA USA

Re: Help fix my GB24?

Post by blakestree »

Bad switch, ja?
While leaves shall fall, do branches intertwine, that we remain bound.

Blake's Tree
Top
User avatar
JonnyAngle
IAMILFFAMOUS
IAMILFFAMOUS
Posts: 4233
Joined: Wed Feb 25, 2015 11:35 am
Contact:
Contact JonnyAngle

Re: Help fix my GB24?

Post by JonnyAngle »

crochambeau wrote:
JonnyAngle wrote:All of the wires soldered to the switch have good connections and pass continuity. I emailed Scott, but I'm not patient. Especially if it's something I can do myself.
How far "in" have you confirmed continuity?

Have you measured voltages on the Vcc pins yet?
Nope

I tested to make sure all of the wires to and from the PCB are good. I don't know how to do diddly squat with a populated PCB. The switch is working, I tested that as well.

Shipping it to Canada, Scotty's going to get his mitts on it!!! :!!!:
Top
Post Reply

Return to “General Gear”