Peavey F800B Preamp PCB

ryan_biggamepedals · Post by **ryan_biggamepedals** » Sun Sep 11, 2016 4:26 pm

Hi, I made a run of pedals that were derived from an early F800G Super Festival amp, and I have some pcbs left over. Anyways, if you're interested I'll put a link to my site. they are $11 and I put up a build doc and drill template. Here is what it looks like, but its green, and the trim pot is a bigger 9mm one. Also it doesn't say all that stuff

http://biggamepedals.bigcartel.com/prod ... preamp-pcb

[

DRodriguez · Post by **DRodriguez** » Sun Sep 11, 2016 5:12 pm

Ordered 2.

One to mess up, one to get right!

ryan_biggamepedals · Post by **ryan_biggamepedals** » Sun Sep 11, 2016 7:11 pm

Haha nice! I was pulling my hair out trying debug a couple of these guys. Just watch your electro cap orientation and resistor values and you should have two working pcbs!

Iommic Pope · Post by **Iommic Pope** » Sun Sep 11, 2016 9:02 pm

Just got two.
Should make a good Christmas present for someone if I get off my arse and built it.
And then one for me!

Aquietcabin1978 · Post by **Aquietcabin1978** » Sun Sep 11, 2016 10:49 pm

Oh man that is rad!

eatyourguitar · Post by **eatyourguitar** » Mon Sep 12, 2016 10:28 pm

I can trade you a fuzz factory PCB for a F800G PCB its like the same price almost on my site.

Iommic Pope · Post by **Iommic Pope** » Mon Sep 12, 2016 10:34 pm

Question for ryan_biggame, is there a way to add switch between clean and dirty gains, like add a footswitch and have two gain pots?

ryan_biggamepedals · Post by **ryan_biggamepedals** » Tue Sep 13, 2016 6:49 pm

eatyourguitar wrote:I can trade you a fuzz factory PCB for a F800G PCB its like the same price almost on my site.

Sure, shoot me a message and we can work something out

Iommic Pope wrote:Question for ryan_biggame, is there a way to add switch between clean and dirty gains, like add a footswitch and have two gain pots?

Yes, but the volume just from clean to distorted is pretty massive. What you can do is disengage the gain pot and use two volume controls. It's not super easy with this pcb, but I can send you a schematic if you would like.

Iommic Pope · Post by **Iommic Pope** » Tue Sep 13, 2016 8:35 pm

That could be rad!
Thanks man!

eatyourguitar · Post by **eatyourguitar** » Mon Oct 31, 2016 3:00 pm

took me a few minutes to sort out that you actually wire the jacks to the PCB then PCB to footswitch then back to the PCB then back to the footswitch then back to the PCB then from the PCB to the jack.

eatyourguitar · Post by **eatyourguitar** » Mon Oct 31, 2016 3:05 pm

really need a build doc here anyone have it?

DRodriguez · Post by **DRodriguez** » Mon Oct 31, 2016 3:29 pm

eatyourguitar wrote:took me a few minutes to sort out that you actually wire the jacks to the PCB then PCB to footswitch then back to the PCB then back to the footswitch then back to the PCB then from the PCB to the jack.

Sent you the build doc, but what? That has me all confused.

Maybe that's what I messed up in my build, but I don't think so.

I wired jacks to the pcb up top, and foot switch to the connections on the bottom.

eatyourguitar · Post by **eatyourguitar** » Mon Oct 31, 2016 3:59 pm

yeah but if you think about it the signal goes in an out of the PCB two extra times compared to most other guitar pedals. makes the wiring cleaner maybe but I actually think it just makes the build more complicated. I got the PM thanks.

eatyourguitar · Post by **eatyourguitar** » Mon Oct 31, 2016 4:00 pm

can I use max1044 instead of ICL7660?

eatyourguitar · Post by **eatyourguitar** » Mon Oct 31, 2016 4:30 pm

I found 7660 on mouser all set

ilovefuzz.com

Peavey F800B Preamp PCB

Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB

Re: Peavey F800B Preamp PCB