Let's see your finished DIY projects!

[theavondon]

First build! Got bored, decided to buy the parts I didn't have to build a LPB-1. I found the tagboard and transistor at work, and then picked up some more components and the switch, and had the enclosure around my house. The store I drove to (Again, impulse build) didn't have stomp switches. I might get one later down the road, but at this point, I'm stoked it fired up the first time. And, it only took me the length of three Modest Mouse albums to build.

[culturejam]

nice, work mang!

[theavondon]

nice, work mang!

I have a feeling an addiction is coming on.

[skullservant]

NICE! Love the tagboard

[the Life Aquatic]

LPB-1 was my first build too! I was discouraged and didn't build much after that because I thought i fucked up the build since when the knob was at zero it killed the signal lol got an real LPB-1 later on and just laughed when I saw that did it too.

[zRobertez]

And, it only took me the length of three Modest Mouse albums to build.

Of approximately 15+ songs on each exactly how my first build was

[LaoWiz]

nice, work mang!

I have a feeling an addiction is coming on.

Yes, you are fucked

[culturejam]

I likes to trawl ebay for cheap busted pedals on the cheap and fix 'em up. 8) Saw one the other day I could not pass up: a ProCo Brat in hot pink for $28 shipped. Seller said the input jack was intermittent, so I figured it would be an easy fix. And it was.

The input jack's solder pins had broken free of the joint and pads. I'm sure it was because a previous owner lost the input jack nut, and the strain from inserting and removing cables eventually caused the stress fracture in the joints. Reflowed the joints and she was good to go.

But I also cleaned it up a bit. It was pretty gross and neglected, so I cleaned off the dirt and gave it a decent once-over spit shine. Looks pretty nice now, if you like Aqua Net pink.

I will be adding a 9v jack to this one. Other than that, I'll most likely leave it stock. The overall tone is not exactly mind-blowing. After tracking down a schematic (drawn by SoulSonic), I see how it differs from the Rat: it has feedback loop clipping diodes as well as the typical clippers to ground. And that sort of makes it the granddaddy of the BJFE Honey Bee. I was not impressed with the Honey Bee, so it's no shock I don't like a really similar setup in the Brat. Still, I have a couple Rats kicking around, so there's not need for me to mod this one to make it more Rat-like. Viva la difference!

Some pics:


Brat as received from seller:




Tape FTW!



Nice inside packing job:




The enclosure is really cool. Every plane is its own part (back, front, top, bottom, sides).




Dirty!




Board shot:




LM308 goodness:




Back side:




Detail of bad joints (bottom three):




All clean!





I will post some final pics once I have the 9V jack installed.

[skullservant]

Awesome!

[theavondon]

Dude, score.

[soldersqueeze]

Back side:

I love any pedal with weird shit written on the PCB. I think my RRR has some little message on it, and it makes me feel special

[zRobertez]

My first mod! I changed the depth switch to a knobby and now the switch kills the dry signal so I can vibrato out all night.
There is one problem though. I need to add true bypass at some point because with the vibrato switch on, it kills the dry signal even in bypass. Oh well. I dig it!

The guys aren't really worth looking at. It's just moving wires around mostly.

[ran_dizolph]

Just wrapped up my first attempt at etching. Super HardOn clone.

Took a couple of stabs at getting the transfer on, but still far from perfect. Might need to go a bit easier on the acid ratio next time around. Also used the sponge method for applying it, and may have put too much pressure on it, so I think I'll just do it upside down in the pan next time, and gently agitate it.

Was hoping to paint the inset, but there was just too much pitting around some of the detail to do it. Next time!

[skullservant]

Looks good man!

I built this up for myself last night to take a break from stuff on the bench and mounting hardware.

It's a Madbean Cavedweller with a few tweaks. Found the PERFECT capacitor value for the repeat color that also keeps your dry signal when the repeats are on 100% faithful to when bypassed instead of coloring it. Also added a photoresistor with a pot to control the intensity of the warbles that you can create, as it is hooked up to the delay time knob.

[Jero]

Just wrapped up my first attempt at etching. Super HardOn clone.
Took a couple of stabs at getting the transfer on, but still far from perfect. Might need to go a bit easier on the acid ratio next time around. Also used the sponge method for applying it, and may have put too much pressure on it, so I think I'll just do it upside down in the pan next time, and gently agitate it.
Was hoping to paint the inset, but there was just too much pitting around some of the detail to do it. Next time!

Might be my favorite pedal pun yet.