ilovefuzz.com

Seppuku PLL :Oscillatory Resynthesizer:
Seppuku PLL :Oscillatory Resynthesizer:
http://www.seppukufx.com/oscillatory%20 ... esizer.htm

NOT ENOUGH KNOBS

Lao wiz has all sorts of win over that visually. I'm also assuming he will in knob terms as well

Ha.

Knob terms.

goroth wrote:Lao wiz has all sorts of win over that visually. I'm also assuming he will in knob terms as well

Ha.

Knob terms.

Thanks, man! Finishing up some stuff for Holy Schnikes over the weekend and then I'll land back in PLL land. Got some ideas that I want to hash out. There will definitely be more knobs and more fuzz!

LaoWiz wrote:

goroth wrote:Lao wiz has all sorts of win over that visually. I'm also assuming he will in knob terms as well

Ha.

Knob terms.

Thanks, man! Finishing up some stuff for Holy Schnikes over the weekend and then I'll land back in PLL land. Got some ideas that I want to hash out. There will definitely be more knobs and more fuzz!

OH FUCK YES

just ran the infanem second voice into my pllollol and it is indeed some diabolical shit
with the non fuzz mode on they just fight each other and chirp and bleep non stop
but running the second voice fuzz on into the pll helped it track and pitch nicely

it seems to run better with neck pickups and on bass
super touchy atleast mine is but its super fun!!

tuffteef wrote:it seems to run better with neck pickups and on bass
super touchy atleast mine is but its super fun!!

The more I hear, the more I want one...

tuffteef wrote:just ran the infanem second voice into my pllollol and it is indeed some diabolical shit
with the non fuzz mode on they just fight each other and chirp and bleep non stop
but running the second voice fuzz on into the pll helped it track and pitch nicely

it seems to run better with neck pickups and on bass
super touchy atleast mine is but its super fun!!

You get your board working? Been following the thread at DIYstomp.

LaoWiz wrote:

tuffteef wrote:just ran the infanem second voice into my pllollol and it is indeed some diabolical shit
with the non fuzz mode on they just fight each other and chirp and bleep non stop
but running the second voice fuzz on into the pll helped it track and pitch nicely

it seems to run better with neck pickups and on bass
super touchy atleast mine is but its super fun!!

You get your board working? Been following the thread at DIYstomp.

multiplier works the divider is still dead its driving me bat shit
someone else is having the same problem though
ive been staring at tracks and the schem checking it over and over

tuffteef wrote:

LaoWiz wrote:

tuffteef wrote:just ran the infanem second voice into my pllollol and it is indeed some diabolical shit
with the non fuzz mode on they just fight each other and chirp and bleep non stop
but running the second voice fuzz on into the pll helped it track and pitch nicely

it seems to run better with neck pickups and on bass
super touchy atleast mine is but its super fun!!

You get your board working? Been following the thread at DIYstomp.

multiplier works the divider is still dead its driving me bat shit
someone else is having the same problem though
ive been staring at tracks and the schem checking it over and over

Dude, that sucks. Divider with the other sounds is what makes this shit good. Maybe wait awhile before fiddling too much so you don't fuck up the PCB. The build probably should have been verified before unleashed to peeps. My board is coming in a couple of days but gonna wait on building it. Hang in there I'm sure someone will figure this shit out...

The pots being backwards is confirmed, and the divider section not working has a workaround. The workaround is as follows;

1) Cut the PCB trace between pins 2 and 15 on IC7.
2) Cut the PCB trace between pin 5 of IC4, and the COM pin of the Divider switch (SW2).
3) Run a jumper from pin 2 of IC7, to pin 5 of IC4.
4) Run a jumper from pin 15 of IC7, to the COM pin of the Divider switch (SW2).

The pots will have to be wired, instead of soldered directly. The rotary switches are OK.

The board should work fine with that. I know it's a PITA insofar as the pots and workaround are concerned, but at least the boards are not DOA.

digi2t wrote:The pots being backwards is confirmed, and the divider section not working has a workaround. The workaround is as follows;

1) Cut the PCB trace between pins 2 and 15 on IC7.
2) Cut the PCB trace between pin 5 of IC4, and the COM pin of the Divider switch (SW2).
3) Run a jumper from pin 2 of IC7, to pin 5 of IC4.
4) Run a jumper from pin 15 of IC7, to the COM pin of the Divider switch (SW2).

The pots will have to be wired, instead of soldered directly. The rotary switches are OK.

The board should work fine with that. I know it's a PITA insofar as the pots and workaround are concerned, but at least the boards are not DOA.

Good work, Dino!

Word up guys. Seems some of you will be able to get some PLL-esque goodness outta this fear not the mods listed above work out

Happy hacking.

LaceSensor wrote:Word up guys. Seems some of you will be able to get some PLL-esque goodness outta this fear not the mods listed above work out

Happy hacking.

they did indeed work and im back in business!!