Page 5 of 112

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 12:44 am
by skullservant
This is Wes Mantooth's custom Maestro FZ-1 into Shin Ei FY-2 with switchable clean blends for each circuit! Just waiting on the enclosure from the almighty DAN to fit the hardware and wire her in.

Image

Next up is Nieh's custom SUPER HARD STAMPEDE 3 stomper in flat black.

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 1:02 am
by nieh
skullservant wrote:Next up is Nieh's custom SUPER HARD STAMPEDE 3 stomper in flat black.


Image

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 1:11 am
by skullservant
Need to stop and pick up some more perf and transistors from the local shop tomorrow, but everything else from Mammoth should be coming either tomorrow or Tuesday hopefully. I think Tuesday I'll have the most time to be able to drill and fit the hardware in when it comes. The enclosure looks plenty roomy for everything

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 9:51 am
by Wes Mantooth
nieh wrote:
Image

I feel the same :thumb:

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 9:54 am
by skullservant
I'll also be ordering some Madbean Cavedweller boards when they drop on the 21st, one of which will be for Excane's, with clean blend, half speed, and oscillation!

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 12:12 pm
by Ghost Hip
DIRGE ELECTRONICS STAMPEDE. FOR THOSE WHO WANT TO BE LOUD.

But really, along with my Umiom, this guy is my go to dirt at the moment.

[youtube]http://www.youtube.com/watch?v=86bdlc8EBjE[/youtube]

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 12:17 pm
by chutneyfarmer
skullservant wrote:I'll also be ordering some Madbean Cavedweller boards when they drop on the 21st, one of which will be for Excane's, with clean blend, half speed, and oscillation!



Fuuuuuuuck, I need to get saving so :) what custom options do you have for the cave dweller? Definitely want the momentary footswitch for teh oscillationz anyway.

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 12:45 pm
by skullservant
@PumpkinPieces: you da bomb dot com. Gonna listen to the video when I get off work later!

@chutney: Well for Excane's I'm doing clean blend, momentary footswitch for oscillation, as well as a stomp switch and extra knob to flipflop between two time settings. I think the only other thing I could really do other than that is add a second momentary switch to dime the time knob back and forth and put that next to the other momentary!

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 1:04 pm
by skullservant
I must note that the final stampede prototype will not feature the SHO unless requested- the second stomp switch on the prototype is for oscillation. I can make a SUPER HARD STAMPEDE like Jareds upon request though!

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 1:08 pm
by skullservant
JUST LISTENED TO THE DEMO SOMEHOW AND IT RULED YOU RULE JARED.

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 2:01 pm
by Ghost Hip
skullservant wrote:JUST LISTENED TO THE DEMO SOMEHOW AND IT RULED YOU RULE JARED.


THANKS MAN COULDN'T HAVE DONE IT WITHOUT YOU.

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 2:02 pm
by skullservant
:!!!:
:hug:

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 4:55 pm
by BlindtoFaith
Stampede sounds sick! Good shit Skully and Pump

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 4:57 pm
by skullservant
Thanks man!

Re: DIRGE ELECTRONICS

Posted: Mon Jul 16, 2012 9:48 pm
by skullservant
Got the knobs for Nieh's Super Hard Stampede today. Going to be drilling the enclosure tomorrow!

Image

These will be either Gloom Drive Deluxes or Stampede Juniors.
Stampede Juniors are two knobbed versions of the regular stampede. Simply Master Volume and oscillation control, with a switch for toggling oscillation on and off.

Image

Stay tuned!