ilovefuzz.com

bronzetalon wrote:

Tompski wrote:

Raintes wrote:Don't say the "C" word 'round here.

Did I say the wrong thing?

Its been asked before...you aint getting a compressor form the good doc. Go grab a diamond compressor and be done with it.

Or get the empress and really be done with it.

Ok got it!

Part 4! Synced

[youtube]http://www.youtube.com/watch?v=ucvQfqM4DmI[/youtube]

Just got back from holidays and found a Cosmi waiting on the kitchen table (gotta love having in laws checking the post). So much zombie fun. Thanks Ryan!

bronzetalon wrote:Part 4! Synced

Does the second expression jack control the clock knob or does it allow me to change the lfo shape and depth?

There are not words yet invented to describe my joy for this box so I will say that it is erasculitiously meinfergating and vorculatious

The controls are very different from what I'm used to on chorus type effects, but they're actually becoming fairly intuitive. I was wondering about the CV-in for tempo, could you just use an external tap-tempo thinger that wasn't CV? I have a DMMTT550 that has an external tap tempo input, and I was wondering if I could rig something up to send a single tap-tempo signal to both pedals.

hollowhero wrote:Does the second expression jack control the clock knob or does it allow me to change the lfo shape and depth?

Rate and depth, I used depth in my video because if I used rate it would modulate through a sweep of rates.

wfs1234 wrote:There are not words yet invented to describe my joy for this box so I will say that it is erasculitiously meinfergating and vorculatious

The controls are very different from what I'm used to on chorus type effects, but they're actually becoming fairly intuitive. I was wondering about the CV-in for tempo, could you just use an external tap-tempo thinger that wasn't CV? I have a DMMTT550 that has an external tap tempo input, and I was wondering if I could rig something up to send a single tap-tempo signal to both pedals.

Basically no you need something that has a cv out. The tap tempo in on your dmm is merly looking for a momentary switch to set tempo. The ccv3 has no way to directly take a tap tempo like that.

Thanks! I was really hoping for it to be a tap tempo inputs so I could just plug one momentary switch into both for kewl synchronized delays and chorusing, will have to work on a cv solution to this...

A copilot broadcast with two outputs might work.

Awesome synced video, Ian, that's really cool!

wfs1234 wrote:Thanks! I was really hoping for it to be a tap tempo inputs so I could just plug one momentary switch into both for kewl synchronized delays and chorusing, will have to work on a cv solution to this...

Pedals that you can do that are digital and already have a computer inside that can make tap tempo, it's not like the Cosmi at all. I hear this a lot, people think you can just 'plug in' tap tempo but that's now how it works.

Tap tempo requires a computer to count how many times the stomp switch touches ground and then convert that timing into a bpm or specific rate based off that counter. It requires a full microprocessor with a page or two of code and you have to interface a digital control section with the analog section. It's a big complicated addition to an analog circuit and depending on the nature of the analog clock circuitry, might not even be possible.

Expression/CV inputs just require a waveform/voltage plugged in, that's all they can work with, it's an analog system.

[youtube]nLFS9rvE1b4[/youtube]

#42

Tompski wrote:[youtube]nLFS9rvE1b4[/youtube]

#42

There ya go

[youtube]http://www.youtube.com/watch?v=nLFS9rvE1b4[/youtube]

Tompski wrote:[youtube]nLFS9rvE1b4[/youtube]

#42

Nice demo Tompski, much better tone and playing than my half baked demos.

Thanks Excane! I was there for flipping ages trying to work that out! What was I doing wrong? I managed to do it right on The Gear Page.

And thanks Bronzetalon, I like your demos