Page 241 of 408
Re: Let's see your finished DIY projects!
Posted: Mon Jun 17, 2013 6:41 pm
by ThePastRecedes
18 volt big muff pi
Re: Let's see your finished DIY projects!
Posted: Mon Jun 17, 2013 6:55 pm
by intothegroove
Love this! excellent stuff
Re: Let's see your finished DIY projects!
Posted: Wed Jun 19, 2013 1:04 pm
by soldersqueeze
I'm on a boxing-up marathon! This one is a phase 45 (madbean smoothie) into delay (grind custom de profundis). Both are great sounding boards.
Re: Let's see your finished DIY projects!
Posted: Wed Jun 19, 2013 4:22 pm
by eatyourguitar
analog delay + feedback looper. removed the PCB that had the pots on it. cut the main PCB to make it smaller. hacked the bypass flip-flop for default ON when powered up. jumpered all the grounds that get broken when you remove that second PCB, like 6 of them. there was a lot of reverse engineering to do what looks like a simple job. I think it would have been easier to build something from scratch.
from this
to this
[youtube]http://www.youtube.com/watch?v=jPtzw1AtIGk[/youtube]
Re: Let's see your finished DIY projects!
Posted: Wed Jun 19, 2013 5:24 pm
by intothegroove
Re: Let's see your finished DIY projects!
Posted: Wed Jun 19, 2013 5:51 pm
by Mike
How big is that Fresnel lens in the middle, and, if you don't mind me asking, where did you get it...?
Re: Let's see your finished DIY projects!
Posted: Wed Jun 19, 2013 8:28 pm
by ThePastRecedes
Devi ever torn's peaker with an ehx lpb-1 as an after booster
Re: Let's see your finished DIY projects!
Posted: Wed Jun 19, 2013 10:17 pm
by eatyourguitar
Mike wrote:How big is that Fresnel lens in the middle, and, if you don't mind me asking, where did you get it...?
HMC461-CTPit is listed as a 10mm lens. I think it might actually be a little bigger than that though. lots of room in there, I just filled it with hot melt glue and teflon tubing to prevent shorts. if they start making fresnel lenses that are the perfect size for a silonex LDR, I will be on it. so far this was my best option. devi uses
SJ-5312 CLEAR from 3M. they get yellow over time and I think they look like some DIY resin molded thing so even though I have them I used the vcc fresnel instead.
Re: Let's see your finished DIY projects!
Posted: Mon Jun 24, 2013 3:47 pm
by LaoWiz
Rosac Nu Fuzz for Holy Schnikes
Re: Let's see your finished DIY projects!
Posted: Mon Jun 24, 2013 3:52 pm
by intothegroove
Fuck yea! Beautiful
Re: Let's see your finished DIY projects!
Posted: Mon Jun 24, 2013 4:04 pm
by LaoWiz
intothegroove wrote:Fuck yea! Beautiful
Thanks, mang!
Re: Let's see your finished DIY projects!
Posted: Mon Jun 24, 2013 4:06 pm
by Holy Schnikes
intothegroove wrote:Fuck yea! Beautiful
Re: Let's see your finished DIY projects!
Posted: Mon Jun 24, 2013 4:07 pm
by skullservant
Holy Schnikes wrote:intothegroove wrote:Fuck yea! Beautiful
Re: Let's see your finished DIY projects!
Posted: Mon Jun 24, 2013 4:09 pm
by Achtane
skullservant wrote:Holy Schnikes wrote:intothegroove wrote:Fuck yea! Beautiful
Also...nice avatar, LaoWiz
Re: Let's see your finished DIY projects!
Posted: Mon Jun 24, 2013 4:13 pm
by LaoWiz
Achtane wrote:skullservant wrote:Holy Schnikes wrote:intothegroove wrote:Fuck yea! Beautiful
Also...nice avatar, LaoWiz
Ha, my old one was tetsuo. The new one was tetsuo but I just changed it to story of ricky.
