ilovefuzz.com

ck3 wrote: Friday Club PD100

I've been really curious about that. I wish it wasn't so new and that there were some gutshots, I'm curious whether it's just another preamp circuit or something more interesting.

John Matrix wrote:

John wrote:Tried my buddy's out this week. Going into a clean amp with no breakup (output level of pedal set low) it's in satisfying at any setting. With the level cranked and the amp breaking up, it's a very different animal and quite pleasing. There's still something not quite right about the EQ but I'm not sure what it is. Also whut up with the "Depth" knob? To my ears it does about nothing!

Are you using it for bass or guitar? Turning the depth knob up reduces the super low frequencies...so I think it's probably only really noticeable on bass. I use mine for guitar so I just turned it all the way up and assumed it is doing something but yeah, can't really tell.

Ah ok that makes sense. Yeah just used it on guitar, but he's using it for bass. He put it on his board today and it did seem to do something very slight, but then again we weren't listening specifically to the very low end so we might have just experienced attentional deafness.

jrfox92 wrote:

ck3 wrote: Friday Club PD100

I've been really curious about that. I wish it wasn't so new and that there were some gutshots, I'm curious whether it's just another preamp circuit or something more interesting.

The PD100 PCB is situated with components on its opposite side, so only the backside of the board is visible when the backplate is removed. It definitely behaves like a preamp, though I have no idea what's going on under the hood.

The shake shack is almost done, just have to do the final wiring.

Etching by Dropping Acid Pedal Etching (JonnyAngle)

And hear I flipped mine for a fuzz face.

I mean, worth cause the fuzz face is amazing. But yea.

That shit looks nuts. Bone Zone is a go!

jrfox92 wrote:

spacelordmother wrote:

jrfox92 wrote:So, after posting the schem I drew up in a FB group

Nice! What do we have to do to bypass the grit and get a beautifully clean 3-band parametric preamp? Bypass the diodes before the high band?

Hey so I was looking for a PCB design project to work on today during downtime at the job, so I turned this into a PCB (**only the EQ section, no distortion**). The vero layout I came up with doesn't work, so rather than troubleshoot I think I'm just gonna order some PCBs now. If anyone wants either a PCB or a finished build get at me some time in the next few days? The PCB is small enough to fit a 125B, but good luck getting 9 knobs in there

Also dang DRod that looks killer!!!!

Dungus wrote:Obviously not new pedals, but Boneshakers are $50 again for Americans, you lucky people.

http://www.harmanaudio.com/professional ... ck#start=1

Back again! (until 7/2! Limit 10 per order )

DRodriguez wrote:The shake shack is almost done, just have to do the final wiring.

Etching by Dropping Acid Pedal Etching (JonnyAngle)

That is delightful.

Functioning! Sounds fucking killer.



Better pics and full run through of the setup when I'm less exhausted.

DRodriguez wrote:Functioning! Sounds fucking killer.



Better pics and full run through of the setup when I'm less exhausted.

This is absolutely nuts.

Aha. What the hell.

How does it sound stacked? Does it get real fucked up?

Faldoe wrote:How does it sound stacked? Does it get real fucked up?

They're parallel.

Sorta.

Each bone shaker gets roughly two strings via sideways pickups. Carried over via a 4 pin xlr cable to the shake shack. And then 3 individual outs in case I want more individualish effects.


(pre finsihed pic)

Sounds meaty. Tons of low end. clear everything. Dynamic and loud. It's like dirty dynamic clarity. I dig the shit out out of it

Wut. Da. Fuq.
Brilliant!