Hey, tell me if this would look terrible or not.

dubkitty · Post by **dubkitty** » Mon Jul 08, 2013 10:47 pm

i'm afraid of 100 grit. for me, 220 is right on the edge of tearing up the wood too much.

skullservant · Post by **skullservant** » Mon Jul 08, 2013 11:02 pm

MAN THAT LOOKS AMAZING SO FAR HOLY SHIT THIS IS GONNA RULE

Ancient Astronaught · Post by **Ancient Astronaught** » Tue Jul 09, 2013 8:55 am

skullservant wrote:MAN THAT LOOKS AMAZING SO FAR HOLY SHIT THIS IS GONNA RULE

AGREED!!!

Achtane · Post by **Achtane** » Tue Jul 09, 2013 11:58 am

Thanks doods :group:

Turns out I'm not going to the gym today so I'll probably sand the front later on.

dubkitty wrote:i'm afraid of 100 grit. for me, 220 is right on the edge of tearing up the wood too much.

Agreed, 220 is normally the lowest I'd go, and it's what I stripped the last one with, but man...that shit took FOREVER. I just can't slave over it that much again.
Even with 100-grit, very little wood is removed unless I hit an edge too hard; feels more like I'm rubbing the sealer away than tearing it out. It will easily mess up the edges, though.

Ancient Astronaught · Tue Jul 09, 2013 12:03 pm

Have you tried 180 grit? When I used to refinish drums I would use 180 to knock it down to bare wood then hit it with 300 to smooth out any scratches and then finally with 600 to make it really smooth yet leave enough grooves for the primer to stick (I'd then sand the primer of course). If your going to be staining it I would do 180 > 300 > 600 > 1200. The 1200 will leave the wood feeling smooth but still rough enough for the stain to take and if you apply any laquer for it to stick as well.

Achtane · Post by **Achtane** » Tue Jul 09, 2013 3:15 pm

Mm, I don't have 180, just 150 and then 220. Maybe the 100 is a bit too much. I'll move it up some.
Yeah, I'm gonna work my way up until it's smooove, then wipe a little water on and sand the grains that raise up two or three times, slap the stain on it however many times it needs, then finish with the Tru-oil.
No Sand-and-Seal BS, no million layers of nitro that take months to cure, no worrying about sanding through anything...glorious.
I am pretty sure the headstock's gonna be black after all, but spraying that is no big deal.

I'll post another stain/oil project here too 'cause after the finish is complete, this one's gonna be on standby until I can pay for pickups and classes :idk:

(in that order)

Achtane · Post by **Achtane** » Tue Jul 09, 2013 8:40 pm

Phew, front's stripped.
Plywood4lyfe
My back will probably never forgive me...

dubkitty · Post by **dubkitty** » Tue Jul 09, 2013 11:01 pm

i hear you on the 220 taking too long thing. it seemed like it took forever just to do the NECK on the Musima.

Mudfuzz · Post by **Mudfuzz** » Tue Jul 09, 2013 11:51 pm

it shouldn't take too long....

Achtane · Post by **Achtane** » Fri Jul 12, 2013 4:21 pm

Raised the grain and sanded back a few times until it was smooth like baby child. Staining time, yo.

I took these right after applying the stain, looks like butt when it's fresh and is being absorbed into the wood at different rates. You have to be really fast and try to blend the stain into itself while wiping. As always, the sides are no fun. Probably best to do them first, actually...oh well.
AW MAN THIS IS THE SCARIEST PART
PLEASE DON'T BE AWFUL WHEN YOU'RE DRY

Achtane · Post by **Achtane** » Fri Jul 12, 2013 7:06 pm

ROUND 2 SON, NOT EVEN DRY YET BUT WHATEVER

Still all splotchy and stuff 'cause of the fresh seepage. I kinda like this amount of...uh, darkness. Saturation?
This is where I stop until tomorrow, hopefully it'll be nice and even by then.

backwardsvoyager · Post by **backwardsvoyager** » Sat Jul 13, 2013 2:59 am

Looks really good! :thumb:

sonidero · Post by **sonidero** » Sun Jul 14, 2013 6:15 pm

Man, looking good Achtane... :thumb:

AxAxSxS · Post by **AxAxSxS** » Sun Jul 14, 2013 6:36 pm

This brings back memories. Looks like it will be rad when you're done.

Achtane · Post by **Achtane** » Sun Jul 14, 2013 6:50 pm

Thanks dudes!
I did another round of stain yesterday, but it felt too saturated so I wiped a little of it away. Without some black dye or something mixed in, it's never gonna be as dark as originally planned but I'm digging it as is. Let it dry today while I did some other crap and tomorrow I'll take pics after wiping a few layers of Tru-oil on. Also started spraying the headstock black.
I wonder if there's something cheaper than Stewmac's pickguard blanks that I could use...

ilovefuzz.com

Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.

Re: Hey, tell me if this would look terrible or not.